ABB AX416 Скачать руководство пользователя страница 35

Страница: 35 / 72

PROGRAMMING…

Config. Sensor A

-----

A: pH Glass

-----

A: Ref. Checking

-----

CONFIG. DIAGS

-----

Off

A: Ref. Alarm

kOhm

CONFIG. ALARMS

Config. Sensor A

CONFIG. ALARMS

Config. Sensor B

Config. Sensor A

Off

5.4

Configure Diagnostics

Note.

The Configure Diagnostics function is applicable only if

Diff. Input

for Sensor A and/or Sensor B is set to

Yes

– see

Section 5.3.

Configure Sensor A

Sensor B configuration (dual input analyzers only) is identical to Sensor A
configuration.

pH Glass Check

Set to

to enable the impedance of the glass electrode circuit to be monitored in order

to provide low glass impedance and out-of-sample/broken cable warnings.

Note.

This frame is displayed only if

A: Probe Type

is set to



A: Electrode

is set to

Glass

– see Section 5.3.

Reference Electrode Check

Set to

to enable the condition of the reference electrode to be monitored in order to

provide:

– an indication of when sensor cleaning or replacement is required
– out-of-sample/broken cable warnings

Sensor B (dual input analyzers only) configuration is identical to Sensor A
configuration.
See Section 5.5.

Reference Alarm

Set the impedence value above which the reference alarm is activated.

Sensor B (dual input analyzers only) configuration is identical to Sensor A
configuration.

See Section 5.5.

Содержание AX416









































































Результаты поиска

Содержание AX416

Отзывы:

Похожие инструкции для AX416

Бренды по названию

Популярные бренды

ABB AX416, Руководство пользователя

Результаты поиска

Содержание AX416

Отзывы:

Похожие инструкции для AX416

Бренды по названию

Популярные бренды