ABB AX416 Скачать руководство пользователя страница 63 | Manualshive

Страница: 63 / 72

background image

61

7

CALIBRATION

Calibrate Output 3

Notes.

• Output 3 (and Output 4) calibration is applicable only if the Option board is fitted

and

analog features enabled – see below.

• Output 3 calibration is identical to Output 2 calibration.

Calibrate Output 4

Note.

Output 4 calibration is identical to Output 3 calibration.

Configure Option Board

Notes.

• This frame is displayed only if an option board is fitted.
• The software detects if an option board is fitted but cannot detect the additional features

available.

• If an option board is fitted, the correct selection must be made below to enable use of the

available features. If an incorrect selection is made, the software menus and frames
associated with that option are displayed in the Operating and Configuration pages but
the features do not work.

Use the

and

keys to enable the features for the type of option(s) fitted:

Analog

– Analog features enabled (comprising two additional analog

outputs, two additional alarm relays, clock and logbook facility).

Pb Dp

– PROFIBUS-DP digital communications features enabled.

Pb Dp

– Both analog and PROFIBUS-DP features enabled.

Alter Factory Code

Set the factory settings access code to a value between 0000 and 19999.

Return to main menu.

Operating Page

– see Section 2.3.

…7.3

Factory Settings

Cal. Output 3

-----

Cal. Output 4

-----

Option Board

Analog

-----

Pb Dp

Alter Fact. Code

0000

Monitoring pH

FACTORY SETTINGS

Option Board
Fitted

and

Analog

Features Enabled

Option Board

Not

Fitted

Option Board Fitted,
Additional Features
Disabled

Redox (ORP)

Dual Redox

pH/Redox (ORP)

«
...
61
62
63
64
65
...
»

Содержание AX416









































































Отзывы:

Нет отзывов

Похожие инструкции для AX416

Бренд: Van Walt Страницы: 2

Бренд: Bante Instruments Страницы: 6

Бренд: Xsens Страницы: 4

Бренд: Eastron Страницы: 2

Бренд: EASTERN INSTRUMENTS Страницы: 3

Бренд: i-SENS Страницы: 50

Бренд: Idexx Страницы: 6

Бренд: IDEAL INDUSTRIES Страницы: 10

Бренд: M-system Страницы: 5

PowerCross-Laser 8 S

Бренд: LaserLiner Страницы: 64

ClimaHome-Check Plus

Бренд: LaserLiner Страницы: 10

MeterMaster Plus

Бренд: LaserLiner Страницы: 104

Бренд: LaserLiner Страницы: 52

LaserRange-Master T2

Бренд: LaserLiner Страницы: 52

Бренд: LaserLiner Страницы: 5

CombiRangeXtender 40

Бренд: LaserLiner Страницы: 84

SuperCross-Laser 2P

Бренд: LaserLine Страницы: 92

MoistureFinder Compact

Бренд: LaserLine Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды