ABB ACQ810 Скачать руководство пользователя страница 19

Страница: 19 / 134

Introduction to the manual 19

Unpack and check the units.
Check that all necessary optional modules and
equipment are present and correct.
Only intact units may be started up.

Mechanical installation

(page

)

If the drive module has been non-operational for
more than one year, the converter DC link
capacitors need to be reformed. Ask ABB for
instructions.

Check the installation site.

Ambient conditions

(page

116

)

Fasten the base of the cabinet to floor. Install the drive
module into the cabinet.

Mechanical installation

(page

)

Route the cables.

Routing the cables

(page

)

Check the insulation of the supply cable, the motor and
the motor cable.

Checking the insulation of the assembly

(page

)

Connect the power cables.
Connect the control and the auxiliary control cables.

Connecting the power cables

(page

Connecting the control unit to the drive module

(page

Connecting the control cables

(page

)

Manuals for any optional equipment

Check the installation.

Installation checklist

(page

)

Commission the drive.

Start-up

(page

)

Operating of the drive: start, stop, speed control etc.

ACQ810-04 quick start-up guide

ACQ810 pump

control program firmware manual

Task

See

Содержание ACQ810







































































































































Результаты поиска

Содержание ACQ810

Отзывы:

Бренды по названию

Популярные бренды

ABB ACQ810, Руководство по оборудованию

Результаты поиска

Содержание ACQ810

Отзывы:

Бренды по названию

Популярные бренды