ABB ACQ810 Скачать руководство пользователя страница 89

Страница: 89 / 134

Installation checklist 89

Installation checklist

What this chapter contains

This chapter contains a list for checking the mechanical and electrical installation of the
drive.

Go through the checklists below together with another person. Follow the

Safety

instructions

on the first pages of this manual.

Mechanical installation

Cabinet construction

Checks for cabinet construction are listed below.

Cabinet construction

1.1

Frame, wall, floor and roof structures, busbar enclosures and cable entries are correct and completely
assembled.

1.2

The drive module is fastened properly to the cabinet. (See

Planning the cabinet installation

and

Mechanical installation.

)

1.3

Mechanical joints are tightened and not broken.

1.4

Parts are clean and painted surfaces not scratched.
The cabinet frame and parts which are in metal to metal contact with the frame (for example seams,
component fixing points on assembly plates, back of control unit mounting plate) are

not

finished with

non-conducting paint or material.

1.5

Degree of protection (IPxx)

1.6

There is a sufficient number of supports, bolts and nuts for cables.

Содержание ACQ810







































































































































Результаты поиска

Содержание ACQ810

Отзывы:

Бренды по названию

Популярные бренды

ABB ACQ810, Руководство по оборудованию

Результаты поиска

Содержание ACQ810

Отзывы:

Бренды по названию

Популярные бренды