manualshive.com logo in svg

909 WLBCF310, Инструкция по эксплуатации

Поделиться
Скачать
909 WLBCF310 Скачать руководство пользователя страница 9

Additional Safety Rules for Petrol Products

•   Do not operate in a hazardous location. Such areas include where 

there is a risk of explosion of petrol fumes, leaking gas or  

explosive dust.

•   Do not operate in a confined area. Exhaust gases, smoke or fumes 

could reach dangerous concentrations.

•   Protect your product.  This Brushcutter / Line Trimmer is  

NOT WEATHERPROOF and should not be exposed to direct sunlight, 

high ambient temperature and damp, wet or high humidity  

conditions.

•   Do not smoke while refuelling. This is potentially dangerous as it may 

ignite the fuel and cause an explosion.

•   Take care not to spill fuel or oil. When refuelling the Brushcutter / Line 

Trimmer ensure that the motor has been switched off. Prevent the 

spilling of fuel as this may also ignite with the hot motor.  

Never refuel whilst the engine running.

•   Check for fuel leaks.  Do not operate if a fuel leak is detected. Where a 

fuel leak is detected, drain the tank of fuel and have the leak repaired.

•   Be careful where you store the Brushcutter / Line Trimmer. Store the 

Brushcutter / Line Trimmer in a dry area away from flammable liquids.

•   Keep your distance. The Brushcutter / Line Trimmer emits exhaust 

fumes. Ensure bystanders keep a safe distance.

•   Never fill fuel tank indoors. Never fill fuel tank when engine is running 

or hot. Do not smoke when filling fuel tank.

 

•  Wear goggles

 

•  Wear earmuffs

 

•  Wear a breathing mask   

7

Содержание WLBCF310











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды