manualshive.com logo in svg

909 WLBCF310, Инструкция по эксплуатации

Поделиться
Скачать
909 WLBCF310 Скачать руководство пользователя страница 27

  WLBCF310    INSTRUCTION MANUAL    www.909.com

25

  WLBCF310    INSTRUCTION MANUAL    www.909.com

Changing the line only on the Spool and Line Assembly

NOTE: 

Always ensure the engine is turned off before undertaking this  

assembly.

NOTE: 

The spool and line assembly supplied with 

this product requires1 length of 2.4mm diameter 
nylon cutting line with a length NOT EXCEEDING 
2.8 metres long. Do NOT attempt to fit larger  
diameter line or length longer than 2.8 metres  
as this will prevent the bump feed to operate  
correctly.
1.   Whilst holding the spool and line assembly (35) 

with the bump knob (34) facing upwards, push 
in the 2 side outer parts of the assembly in  
between where the 2 ribs protrude on  
each side.  
When pushing in both sides at the same time 
the spool cover can be removed. Ensure the 
lines protruding from the eyelets are carefully 
pulled out when you remove the inner spool. 
(Fig. AM)

   NOTE: 

When removing the spool, there is a 

large  1 washer located on each end  
of the spring. Do not lose these. (Fig AN)

2.   Remove any remaining line in the spool.
3.   Prior to fitting the line into the spool and line 

assembly (35), the line needs to be prepared. 
Take a 2.8 metre length of 2.4mm line and halve 
it. Inspect each end of each line and ensure the 
line has no burrs from being cut. 

4.   Fold the full length of line in half and place the 

half way mark of the line into the notch in the 
spool (Fig. AO)

AO.

AM.

AN.

Содержание WLBCF310











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды