manualshive.com logo in svg

909 WLBCF310, Инструкция по эксплуатации

Поделиться
Скачать
909 WLBCF310 Скачать руководство пользователя страница 29

  WLBCF310    INSTRUCTION MANUAL    www.909.com

27

  WLBCF310    INSTRUCTION MANUAL    www.909.com

Prior to operating the line trimmer after line has been added, it is suggested 

to trim the lines so they are even and just short of the cutting blade on the 

guard. This prevents a possible large section of line being trimmed at high 

speed. When you start the line trimmer, bump the head of the spool on the 

ground to enable the cut off knife on the guard to cut the line to the  

required length for use.

Operation of the Line Trimmer

To start the line trimmer, refer to the instructions on page 30 .

NOTE:

 This is a 4 stroke brushcutter / line trimmer.   

The motor MUST be filled with 60mL of SAE 10W/30 BEFORE starting.  

Fresh unleaded fuel must be used in this unit.  
Do NOT use ethanol based fuels.  Do NOT mix oil with fuel.

Use of the Line trimmer

This petrol line trimmer is only made to cut grass.
•    Always use the double shoulder strap harness (31)  

when using the line trimmer to avoid serious personal injury.

•    Perform a few accelerations of the motor without reaching maximum 

speed and without working to make sure that 

everything is in good working order.

•    Start the engine only when you are close to  

the working area.

•    Place yourself in a well balanced position,  

stable on both feet.    

Advancing the line manually

NOTE:

 Always ensure the engine is turned off   

before undertaking this task.
1.   Push the bump knob (34) in while pulling on 

both lines to manually advance the line. (Fig. AU)

2.   Release the bump knob and again pull on both  

lines to advance the line further. (Fig. AV)

3.   If the line still does not advance remove the 

spool and check the lay of the line. It may be 

twisted or trapped under over laying line.

AU.

AV.

Содержание WLBCF310











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды