manualshive.com logo in svg

909 WLBCF310, Инструкция по эксплуатации

Поделиться
Скачать
909 WLBCF310 Скачать руководство пользователя страница 34

32

  WLBCF310    INSTRUCTION MANUAL    www.909.com

  WLBCF310    INSTRUCTION MANUAL    www.909.com

5.   Push the choke (red lever) (22) half way down and allow the motor to  

warm up. Restart if the motor stops.

   Do not pull the cord with a jerk or release it until fully rewound. Provided  

the previous steps have been performed, the motor should start.

6.   Once the engine is fully warm ensure the choke (red lever) (22) is down fully  

to the run position (warm start). 

Warm Start

When re starting the unit after it has been used and the motor is hot, there is no 

need to engage the choke (red lever) (22). Follow steps 4, 5, and 6 above.

A Flooded engine

If the choke (red lever) (22) has been left in the full choke position and the  

engine will not start, it is possible the engine has been flooded  (Too much fuel).
To assist to clear a flooded engine:
1.  Move the choke (red lever) (22) to the run or warm start position. 
2.  Squeeze the safety lever (9), and pull on fully the throttle trigger (8).
3.  Check the on/off switch (10) is on.
4.   Pull the recoil starter (2) a number of times to clear the fuel and start the motor.
 

 WARNING.

  Be aware that if starting occurs with the throttle pressed,  

the motor will accelerate and thus engaging the clutch, which will then 

rotate the cutting head.

 

 As soon as the motor starts release the  throttle so the motor runs at idle  

speed and disengages the clutch.

Adjusting the speed on the Brushcutter / Line Trimmer

NOTE:

 The cutting head (spool and line) will not rotate at the idle speed.   

The cutting head (spool and line) will engage and rotate when the speed of  

the motor is increased.
1.   To increase speed and engage the cutting  

head, squeeze the safety lever (9) and then  

throttle trigger (8). (Fig. BA)

2.   To decrease the speed, slowly release the  

throttle trigger (8) to the desired speed.

3.   To disengage the cutter head (spool and line),  

release all pressure on the throttle trigger (8)  

and allow the motor to return to idle.  The cutter 

head (spool and line) will disengage at idle.

BA.

Содержание WLBCF310











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды