manualshive.com logo in svg

909 WLBCF310, Инструкция по эксплуатации

Поделиться
Скачать
909 WLBCF310 Скачать руководство пользователя страница 22

20

  WLBCF310    INSTRUCTION MANUAL    www.909.com

  WLBCF310    INSTRUCTION MANUAL    www.909.com

Fitting the Brushcutter Blade

NOTE:

 Always ensure the engine is turned off  

before undertaking this task.

NOTE:

 Before fitting, check the diameter of the cutter 

is 255mm, and the Bore size is 25.4mm.  Do NOT  

proceed if the cutter is different to these specifications.
1.  Lay the unit down so that the fuel tank bracket   

(38) is on the ground or on a secure surface. Lift the 

gearbox end of the lower shaft (15) to gain access to 

the spindle (20).

2.  Place the inner flange (30) over the spindle (20)  

ensuring the flats on the spindle (20) align with the flats in 

the inner flange (30).  Fully seat the inner flange. (Fig AB)   

3.  Place the 3T brushcutter blade (28) over the spindle 

(20) and locate on the raised centre of the inner flange 

(30). (Fig AC) .  Ensure the direction of rotation of the blade as indicated by an  

arrow on the blade corresponds with the arrow direction on the top of the guard.

4.  Place the outer flange (29) over the spindle (20) on top of the 3T brushcutter 

blade (28) (Fig. AD), followed by the protector (27).

5.  Place the blade nut (26) on to the spindle (20) and thread the nut in an anti  

clockwise direction all the way down to the protector (27). (Fig. AE)

6.  To fully tighten the 3T brushcutter blade (28) onto the spindle (20) ensure the  

3T brushcutter blade (28) is still correctly located on the inner flange (30).

7.  Insert the long end of the supplied 4mm allen key (36) through the spindle lock 

hole (19) and into the hole on the inner flange (30).  (This locks the spindle  

allowing the blade bolt to be secured) (Fig. AF)

8.  Whilst holding the supplied allen key (36) in position to lock the spindle, use the 

supplied blade nut wrench (36) to fully tighten the blade nut (26) and secure 

the 3T brushcutter blade (28) into position. Ensure the 3T brushcutter blade (28) 

is secured tight before removing the allen key (36) from the spindle hole. 

AB.

AC.

AD.

AE.

AF.

Содержание WLBCF310











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды