manualshive.com logo in svg

909 WLBCF310, Инструкция по эксплуатации

Поделиться
Скачать
909 WLBCF310 Скачать руководство пользователя страница 15

  WLBCF310    INSTRUCTION MANUAL    www.909.com

13

  WLBCF310    INSTRUCTION MANUAL    www.909.com

5.   Check the oil mark on the dipstick.  It should be 

approaching the top mark on the dipstick  
(Fig C).  Be careful not to overfill. (Fig D)

6.   If the oil level is not close to the top oil mark line, 

then add small amounts of oil and  
repeat steps 3,4 & 5 until the oil level is  
approaching the top oil mark on the dipstick.  
DO NOT OVERFILL. Do Not EXCEED the upper 
mark on the dipstick.

7.   

IMPORTANT:

  The motor should NEVER be 

started if the oil level is below the low oil mark. 
Always check the oil level before starting  
ensuring the brushcutter / line trimmer is  
positioned as per step 1 for checking.

8.   When the oil level is at the upper oil level mark, 

replace the dipstick and thread in the dipstick in 
a clockwise direction until the dipstick is firmly in 
place. The Sealing O ring on the shoulder of the  
dipstick should be fully compressed when  
the dipstick is firmly hand tightened. 

C.

UPPER   LOWER 

 MARK     MARK

D.

DO NOT 

OVER FILL

Содержание WLBCF310











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды