manualshive.com logo in svg

909 WLBCF310, Инструкция по эксплуатации

Поделиться
Скачать
909 WLBCF310 Скачать руководство пользователя страница 36

34

  WLBCF310    INSTRUCTION MANUAL    www.909.com

  WLBCF310    INSTRUCTION MANUAL    www.909.com

Repairs

Repairs beyond those described above, should only be undertaken by 

trained personal. Should a malfunction occur do not use the unit any further 

and do not attempt to repair it yourself. Contact Customer Service or have 

the unit repaired by an approved Service Agent.

Maintenance
Air filter

Accumulated dust in the air filter will reduce engine efficiency, increase fuel 

consumption and allow abrasive particles to pass into the engine.
Remove the air filter as often as necessary to maintain a clean condition.
•    Remove the air filter cover (3) by pressing in the single tab and pulling the 

filter cover towards you. Then remove the filter cover fully by unlatching 

the 2 hinges at the bottom.

•   Light surface dust can readily be removed by tapping the filter.
•   Heavy deposits should be washed out in suitable detergent.
•  Do not use petrol or other chemical cleaners/solvent.
•  Squeeze out the remaining water and allow the filter to completely dry.
•  Add a drop of thin oil to the filter and replace it.
•   The air filter should be changed after approximately every 50 hours or 

sooner when used in high dust environments.  

Replacement air filters are available for purchase from our website  

www.extrabattery.com.au.

Fuel Filter

•  The fuel tank is fitted with a filter.
•   Filter is situated at the free end of fuel pipe and can be picked out through 

fuel port with a piece of hooked wire or the like.

•   Check the fuel filter periodically. Do not allow dust to enter the fuel tank. 

Clogged filter will cause difficulty when starting engine or abnormalities in 

engine performance.

•  When the filter is dirty, replace the filter.
•   When the inside of the fuel tank is dirty, it can be cleaned by rinsing the 

tank out with petrol.

•   The fuel filter should be changed only when it is showing signs of  

blockage or there is insufficient fuel being supplied to the motor.

Replacement fuel filters are available for purchase by from our website 

www.extrabattery.com.au.

Содержание WLBCF310











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды