manualshive.com logo in svg

909 WLBCF310, Инструкция по эксплуатации

Поделиться
Скачать
909 WLBCF310 Скачать руководство пользователя страница 26

24

  WLBCF310    INSTRUCTION MANUAL    www.909.com

  WLBCF310    INSTRUCTION MANUAL    www.909.com

   Keep these components in a safe place. The 3T 

brushcutter blade (28) should be placed back in 

the cardboard packaging/envelope.

2.   Place the spool and line assembly (35) on the 

spindle (20) and thread on to the spindle finger 

tight in an anti clockwise direction all the way 

down untill the back of the spool makes contact 

with the inner flange (30). (Fig AK)

3.   Insert the long end of the supplied 4mm allen 

key (36) through the spindle lock entry hole (19) 

and into the hole on the inner flange (30).   

(This locks the spindle allowing the spool and 

line assembly (35) to be secured). Further tighten 

the spool and line assembly (35) ensuring the 

assembly is tight on the spindle (20) and inner 

flange (30) before removing the 4mm allen key 

from the spindle hole to release the spindle  

being locked. (Fig. AL)

Removing the Spool and Line Assembly

NOTE:

 Always ensure the engine is turned off before undertaking this assembly.

1.   Lay the unit down so that the fuel tank bracket (38) is on the ground or 

on a secure surface. Lift the gearbox end of the lower shaft (15) to gain 

access to the output spindle (20).

2.   Insert the long end of the supplied 4mm allen key (36) through the  

spindle lock entry hole (19) and into the hole on the inner flange (30).   

(This locks the spindle allowing the spool and line assembly to be  

removed).  (Fig. AL)

3.   Loosen the spool and line assembly (35) in a clockwise direction until it 

can be removed from the spindle (20).  Remove the allen key (36) locking 

the spindle (20) once the spool and line assembly (35) has been removed.

NOTE:

 If replacing the spool and line assembly (35) with the supplied  

additional assembly, follow the “Fitting the Spool and Line Assembly on the 

Line Trimmer” instructions on the previous page. 
If replacing just the spool line on the supplied spool and line assembly,  

refer to the instructions following this section.

AL.

AK.

Содержание WLBCF310











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды