909 WLBCF310 Скачать руководство пользователя страница 40

Страница: 40 / 42

WLBCF310 INSTRUCTION MANUAL www.909.com

Troubleshooting

Problem

Possible Cause

Solution

Power loss or

sudden stopping

of the engine

Fuel Tank (6) is empty

The mixture does not reach the

carburettor.
There is water in the mixture.

The air filter (3) is dirty.
There are carbon deposits in the cylinder

exhaust pipe or the muffler.
Flooded engine.

Check whether the fuel tank (6) is empty

and refuel if required.

NOTE:

If the trimmer is being used a lot on

its side, the tank may require a minimum of

1/4 tank of fuel.
Clean the fuel filter in the fuel tank (6).

Drain and rinse the fuel system.
Refill the fuel tank (6) with new

uncontaminated fuel.
Clean the air filter (3).
Clean or change the muffler.

Take the product to a Service Agent.

Move the choke to the run or Hot start

position and restart the unit.

Bad quality cut from

the line trimmer

Overloaded cutting due to too high

grass or too thick for engine power.
Wrapped vegetal material on the

cutting tool.
Line will not advance.

Line welded to itself.

Not enough line on the spool.

Line worn too short.

Line tangled on spool.

Cut tall grass from the top down.

Clean the material from the spool and line.

Manually advance the lines.
Open the spool and line assembly (35) and

ensure the lines have not crossed or tangled.
NOTE: Always ensure the engine is turned

off before undertaking this task.
Lubricate with silicone spray.
Manually advance the lines.
NOTE: Always ensure the engine is turned

off before undertaking this task.
Install more line.
NOTE: Always ensure the engine is turned

off before undertaking
this task.
Pull lines while alternately pressing down

on and releasing bump knob (34).
Remove line from the spool and rewind.

Engine does not

reach full speed

Check the fuel.
Check oil reservoir (24) level.
Check spark plug (1).

Use fresh fuel. Do not use ethanol based fuel.
Top up the oil if it is low.
Clean or replace if dirty or worn.

3T Brushcutter

Blade (28) rotates

at idle speed.

The Blade is not securely fitted.
The blade only rotates on run down of

the motor. i.e 5 seconds.
At idle the 3T brushcutter blade (28) is

rotating under power from the motor.

Ensure the blade nut is tightened (26)
This is normal but should not continue to

rotate under power from the motor at idle.
Immediately turn off the motor and take

the product to an authorized

Service Agent.
DO NOT continue to use the product.

For other issues not covered in this chart, please call Customer Service on 1800 909 909.

Содержание WLBCF310











































Результаты поиска

Содержание WLBCF310

Отзывы:

Бренды по названию

Популярные бренды

909 WLBCF310, Инструкция по эксплуатации

Результаты поиска

Содержание WLBCF310

Отзывы:

Бренды по названию

Популярные бренды