3M 900AST Series Скачать руководство пользователя | Manualshive

Страница: 39 / 60

background image

3M

™

Advanced Systems Tester 900AST Series

39

Single Trace

Insert the supplied coaxial TDR test lead into the

Red and Black test jacks on the 900AST tester.

Connect one TDR test lead to a single conductor

or one side of a pair under test. Test lead polarity

is not important for TDR measurements. If a single

conductor circuit is being tested, connect the other

TDR test lead to another de-energized conductor

near the conductor under test. TDR pulses occur at

such a high frequency that an adjacent conductor

can serve effectively as a ‘return’ for the pulse.

Ground or cable shield can also be used for the

return if desired, but this often results in a very

“noisy” trace and is not recommended. If a pair of

conductors is being tested, place the other test lead

on the second conductor of the pair. Single Trace is

used to view events on a single circuit at a time.

«
...
37
38
39
40
41
...
»

Содержание 900AST Series





























































Отзывы:

Нет отзывов

Похожие инструкции для 900AST Series

WJHD309A - DIGITAL DISK RECORDER

Бренд: Panasonic Страницы: 79

Бренд: YYZ Lighting Страницы: 3

Бренд: Camp Safety Страницы: 118

Бренд: Ultrafast Systems Страницы: 39

Бренд: Mackworth Страницы: 2

Бренд: CAMPAGNOLA Страницы: 209

Бренд: Rain-Flo Irrigation Страницы: 16

Бренд: Datavideo Страницы: 28

Бренд: Taylor-Wharton Страницы: 25

Бренд: i-CAT Страницы: 96

Бренд: M-system Страницы: 5

Бренд: MA Страницы: 2

Бренд: Safety 1st Страницы: 4

Бренд: Safety Engineering Страницы: 5

Бренд: TEC Страницы: 6

Бренд: U Technology Страницы: 6

Бренд: Zell Страницы: 32

Бренд: Uflex Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды