3M 900AST Series Скачать руководство пользователя | Manualshive

Страница: 23 / 60

background image

3M

™

Advanced Systems Tester 900AST Series

23

Self-Calibration

Use this function to calibrate the 900AST tester

anytime the outside temperature changes by more

than 35°F (20°C). Calibrate the 900AST tester at

the same temperature at which it will be used.

Note: Initiate a self-calibration prior to the very

first use of your 900AST tester.

You will see the following screen as soon as you

select Self-Calibration from the Toolbox.

Short the test leads together, then press

to

continue.

The screen shows “Self-Calibration Complete”
when the calibration is done, or “Self-Calibration
Failed” if the calibration fails. In this last case,
check the test lead connections and try again.

«
...
21
22
23
24
25
...
»

Содержание 900AST Series





























































Отзывы:

Нет отзывов

Похожие инструкции для 900AST Series

Бренд: Salvis Страницы: 40

Бренд: IDEAL Страницы: 2

Бренд: KaVo Страницы: 13

Бренд: vc999 Страницы: 52

Бренд: Rangevision Страницы: 28

Бренд: Datavideo Страницы: 48

Бренд: Datavideo Страницы: 34

Бренд: Datavideo Страницы: 3

Бренд: Datavideo Страницы: 34

Бренд: Datavideo Страницы: 8

Бренд: Datavideo Страницы: 10

Бренд: Wahl Страницы: 2

Бренд: Zodiac Страницы: 2

Бренд: Zipper Mowers Страницы: 37

Бренд: Zimmer Страницы: 46

Бренд: Harken Страницы: 4

Бренд: Bartscher Страницы: 20

Бренд: Bartscher Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды