3M 900AST Series Скачать руководство пользователя | Manualshive

Страница: 18 / 60

background image

3M

™

Advanced Systems Tester 900AST Series

18

Load Test

This function measures the DC current flowing

through a simulated load lamp inside the 900AST

tester. Connect the Red lead to the conductor under

test and the Black lead to a return or ground. The

900AST tester will continuously display the current

passing through the load as well as a bar graph

representing the approximate level of load lamp

illumination.

If the current in the load is greater than 110 mA, the

following ‘Current Warning’ screen is displayed.

This screen indicates that a high current has been

detected between the test leads and that the 900AST

tester has opened an internal relay to protect itself

from damage. Use standard safety practices for
disconnecting the test leads. Press the

key to

restart the 900AST tester. Fix problems before

restarting the ‘Load’ measurement.

«
...
16
17
18
19
20
...
»

Содержание 900AST Series





























































Отзывы:

Нет отзывов

Похожие инструкции для 900AST Series

Бренд: NEC Страницы: 29

Бренд: e+p Elektrik Handels Страницы: 2

Бренд: KaVo Страницы: 49

Бренд: Easson Страницы: 33

Бренд: IBS Scherer Страницы: 64

Бренд: ParaBody Страницы: 5

Бренд: Gatekeeper Страницы: 8

Bure Rise & Go DB 56-309

Бренд: Gate Страницы: 8

Бренд: Jaga Страницы: 32

Бренд: MacDon Страницы: 46

Бренд: MacDon Страницы: 82

Бренд: Mac Medical Страницы: 2

Бренд: MACDEV Страницы: 8

Mentor Touch ET750

Бренд: MAC TOOLS Страницы: 24

Бренд: MA lighting Страницы: 10

Бренд: QRS Страницы: 16

Бренд: QMAXZ Lighting Страницы: 36

Бренд: Vuly Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды