3M 900AST Series Скачать руководство пользователя

Страница: 4 / 60

™

Advanced Systems Tester 900AST Series

Out of the Box

What you will ﬁnd when you unpack the shipping box:

• 3M

™

Advanced Systems Tester 900AST Series

• Carrying case
• Battery holder and batteries
• Multimeter test leads (red/black pair, blue/yellow

pair, green)

• TDR test leads (two each, coaxial with adapters-not

assembled)

• Instruction manual
• Warranty card

The 900AST tester comes in a sturdy nylon carrying

case and should be used in the case to provide extra

protection from shock and the environment.

The battery holder holds six “AA” standard alkaline

batteries and should be installed prior to using the

unit. Please see the Care and Maintenance section

for battery installation instructions. Always initiate

a self-calibration (see Toolbox – Self Calibrate for

instructions) after installing new batteries.

The 900AST tester comes with two types of test

leads – ﬁve single-conductor test leads (red, black,

green, yellow, and blue) for most DMM (digital multi

meter) functions and two special coaxial test leads for

precision TDR measurements.

For operational information, refer to this manual or

the 900AST tester “Help” screens. For Technical

Service, Warranty or Repair questions call 800 426

8688 (US and Canada) or contact your local 3M

Representative.

Содержание 900AST Series





























































Результаты поиска

Содержание 900AST Series

Отзывы:

Похожие инструкции для 900AST Series

Бренды по названию

Популярные бренды

3M 900AST Series, Инструкция по эксплуатации

Результаты поиска

Содержание 900AST Series

Отзывы:

Похожие инструкции для 900AST Series

Бренды по названию

Популярные бренды