3M 900AST Series Скачать руководство пользователя

Страница: 56 / 60

™

Advanced Systems Tester 900AST Series

Care and Maintenance

Battery Holder

The plastic battery holder that comes with the

900AST tester uses six “AA” alkaline batteries.

Typical lifetime of the alkaline battery pack is

twenty hours of normal use (or less if you use the

backlight frequently or work in very cold weather).
To change the batteries:
1) Loosen the six screws on the battery

compartment door and remove the door.

2) Remove the battery pack from the unit and

unplug the battery connector.

3) Install six fresh alkaline cells in the pack per

the orientation embossed on the battery holder.

WARNING: Do not reverse any batteries or

install improperly in pack.

4) Reattach the battery holder plug and insert the

battery holder in the compartment.

5) Replace the battery compartment door and

retighten screws.

Caution: Batteries may explode, leak or catch fire

if exposed to high temperatures or fire. Recycle or

dispose of properly. To prevent injuries or burns,

do not allow metal objects to contact or short

circuit the battery terminals.

Level of Charge

The battery icon in the upper right of the display

indicates the battery charge. Four black bars in the

icon indicate full charge. Zero black bars indicate

the battery pack is very low and the batteries should

be changed.

Содержание 900AST Series





























































Результаты поиска

Содержание 900AST Series

Отзывы:

Похожие инструкции для 900AST Series

Бренды по названию

Популярные бренды

3M 900AST Series, Инструкция по эксплуатации

Результаты поиска

Содержание 900AST Series

Отзывы:

Похожие инструкции для 900AST Series

Бренды по названию

Популярные бренды