3M 900AST Series Скачать руководство пользователя | Manualshive

Страница: 53 / 60

background image

3M

™

Advanced Systems Tester 900AST Series

53

If this screen is displayed, press the

key to

go directly to the RFL function or the

key to

continue with Auto TDR. Press the

key to exit

the Auto TDR function.

The Auto TDR function completes a TDR trace for

the selected length and analyzes the response.

Note: Auto TDR operates from a captured trace.
The trace is not ‘live’ as in the standard TDR mode.
Changes made to the circuit after the Auto TDR
analysis starts will not be detected or displayed. Vp
can be adjusted while in this mode by using the

and

keys.

If the Auto TDR detects an open circuit, the cursor

is positioned at the location of the open circuit and

OPEN is displayed below the trace. If the Auto TDR

detects a short circuit or low resistance fault, the

cursor is positioned at the location of the short circuit

and SHORT is displayed below the trace.

«
...
51
52
53
54
55
...
»

Содержание 900AST Series





























































Отзывы:

Нет отзывов

Похожие инструкции для 900AST Series

Бренд: MacDon Страницы: 272

Бренд: MacDon Страницы: 70

Бренд: Ecco Страницы: 2

Бренд: Landoll Страницы: 94

Бренд: Panasonic Страницы: 30

Бренд: Dairyland Страницы: 21

Бренд: A.MENARINI Страницы: 2

Бренд: Nakayama Страницы: 37

Бренд: Olsen Страницы: 4

Dominator Series

Бренд: Falcon Страницы: 31

Бренд: Fakir Страницы: 22

Бренд: Wahl Страницы: 2

Бренд: K-LASER Страницы: 70

Бренд: K-LASER Страницы: 72

Бренд: Parkside Страницы: 2

Бренд: Park House Healthcare Страницы: 12

MCX-C15 - MusicCAST Network Audio Player

Бренд: Yamaha Страницы: 114

Бренд: KAM Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды