3Com LS8M1P12TEH Скачать руководство пользователя страница 105

Страница: 105 / 289

Installation Manual
H3C S7500 Series Ethernet Switches

Chapter 4 Hardware Installation

4-9

Figure 4-10

Rear panel of external PoE power supply (PSE2500-A3)

Connect the GND OT terminal of the PoE power cable marked with “GND“ to the

RTN (

) terminal on the switch and fasten the nut. Connect the other end to the

NEG (-) terminal on the panel of external PoE power supply.

5) Connect the PGND OT terminal of the PoE power cable marked with “PGND” to

the grounding screw on the switch and fasten the screw. Connect the other end to

the grounding strip for the switch.

Note:

For the detailed installation procedure of PSE2500-A3, refer to the user manual

shipped with PSE2500-A3.

4.7 Connecting Interface Cables

4.7.1 Connecting the Console Cable

I. Introduction

The console cable is an 8-core shielded cable. It has an RJ-45 connector at one end for

the console port on the switch, and a DB-9 female connector at the other end for a 9-pin

serial port on the configuration terminal. The following figure illustrates the console

cable.

Figure 4-11

Console cable

Содержание LS8M1P12TEH


































































































































































































































































































Результаты поиска

Содержание LS8M1P12TEH

Отзывы:

Похожие инструкции для LS8M1P12TEH

Бренды по названию

Популярные бренды

3Com LS8M1P12TEH, Руководство по установке

Результаты поиска

Содержание LS8M1P12TEH

Отзывы:

Похожие инструкции для LS8M1P12TEH

Бренды по названию

Популярные бренды