3Com LS8M1P12TEH Скачать руководство пользователя страница 275

Страница: 275 / 289

Installation Manual
H3C S7500 Series Ethernet Switches

Appendix B N68 Cabinet Installation

B-77

Note:

In the figure: (1) indicates a dummy panel; (2) indicates a cabling frame; (3)

indicates a nonstandard mini panel

Small squares in the figure indicate guide rails.

A1 through H1 and A2 through H2 are guide rails at the corresponding positions.

M1 through M13 indicate dummy panels at the corresponding positions in the

standard configuration.

In a DC cabinet, you may need to remove the M13 in the upper most, and move the

DC power distribution component which originally locates at the rear of the cabinet

to this position.

In AC cabinets, M13 does not exist, and the position is for the AC power distribution

component.

The S7500 series and other devices that comply with the N68 cabinet size can be

installed in the cabinet.

You need not to use the cabinet exactly as the figure shows, but can adjust the

position of guild rails and dummy panels as needed.

The dummy panels are for comeliness purpose only, so that you need not to install

them when they are in shortage.

The power of your device should be within the range allowed by the air breaker.

Refer to power distribution part for details.

The squares with shadow marks in the figure represent the four-hole guide rails,

which can bear a weight of 90 KG; and the squares without shadow marks represent

the two-hole guide rails, which can bear a weight of 40 KG.

Table B-17

Symbol description

Symbol

Description

Indicates standard configuration (configured with one S7503 chassis)

Configured with two S7503 chassis

Configured with one S7506 chassis

Configured with two S7506 chassis

Configured with one S7506R chassis

Configured with two S7506R chassis

The methods of remodeling standard configuration to other configuration are as

follows:

Remodeling standard configuration to configuration A: Remove dummy panel M7

and M8. The result of the remodeling is configuration A.

Содержание LS8M1P12TEH


































































































































































































































































































Результаты поиска

Содержание LS8M1P12TEH

Отзывы:

Похожие инструкции для LS8M1P12TEH

Бренды по названию

Популярные бренды

3Com LS8M1P12TEH, Руководство по установке

Результаты поиска

Содержание LS8M1P12TEH

Отзывы:

Похожие инструкции для LS8M1P12TEH

Бренды по названию

Популярные бренды