3Com LS8M1P12TEH Скачать руководство пользователя страница 160

Страница: 160 / 289

Installation Manual
H3C S7500 Series Ethernet Switches

Chapter 8 Troubleshooting

8-3

LED

Status

Description

The fan tray is faulty or is not installed yet.

FAIL (Red)

OFF

The fan tray works normally.

If the OK LED is off, check whether:

Each fan works normally.

Something blocks the vents of the chassis.

A blank panel is installed in the slot without a board.

8.4 Troubleshooting SRPUs and LPUs

The SRPG LEDs and LPU

(

ranges from 1 to 6 for the S7506 and S7506R, and from

1 to 3 for the S7503) LEDs respectively show the status of the SRPU and LPU.

Table 8-3

Description of board LEDs

LED

Status

Description

ON/OFF

The board is faulty or is not installed yet.

RUN (Green)

Blinking

The board works normally.

OFF

The board is faulty or is not installed yet.

ALM (Red)

The board works abnormally.

If the ALM LED of a board is solid on, something is wrong with the board. When

you reset a board, the ALM LED will be on, but will be off after it is started to work

normally.

When you reset a board, if the ALM LED stays off, the board may be disconnected

from the power supply. Check whether the board is properly installed.

Содержание LS8M1P12TEH


































































































































































































































































































Результаты поиска

Содержание LS8M1P12TEH

Отзывы:

Похожие инструкции для LS8M1P12TEH

Бренды по названию

Популярные бренды

3Com LS8M1P12TEH, Руководство по установке

Результаты поиска

Содержание LS8M1P12TEH

Отзывы:

Похожие инструкции для LS8M1P12TEH

Бренды по названию

Популярные бренды