3Com LS8M1P12TEH Скачать руководство пользователя страница 7

Страница: 7 / 289

Installation Manual
H3C S7500 Series Ethernet Switches

Chapter 1 Product Overview

1-1

Chapter 1 Product Overview

1.1 Introduction

1.1.1 Introduction to S7500 Series Ethernet Switches

H3C S7500 Series Ethernet Switches (hereinafter referred to as the S7500 series) are

modular, large-capacity L2/L3 Ethernet switches that support wire-speed forwarding.

The S7500 series are designed for IP metropolitan area networks (MANs), large

enterprise networks, and campus networks.

Together with Huawei MA5200 Ethernet Access Management Systems, H3C

S3100/S3600/S5600/S9500 Series Ethernet Switches, and H3C series routers, the

S7500 series can provide comprehensive networking solutions for MANs and

enterprise networks.

Figure 1-1

S7500 series in MAN

The S7500 series support AC and DC power supply redundancy, and now include the

models S7502, S7503, S7506, and S7506R.

The S7502 provides one switching & routing processing unit (SRPU) slot and one

line processing unit (LPU) slot. Both the SRPU and LPU can provide high-density

service ports.

The S7503 provides one SRPU slot and three LPU slots.

The S7506 provides one SRPU slot and six LPU slots.

The S7506R provides two SRPU slots for redundancy backup and six LPU slots.

Содержание LS8M1P12TEH


































































































































































































































































































Результаты поиска

Содержание LS8M1P12TEH

Отзывы:

Похожие инструкции для LS8M1P12TEH

Бренды по названию

Популярные бренды

3Com LS8M1P12TEH, Руководство по установке

Результаты поиска

Содержание LS8M1P12TEH

Отзывы:

Похожие инструкции для LS8M1P12TEH

Бренды по названию

Популярные бренды