Zultys MX250 Hardware Manual Download Page 30

Page: 30 / 62

MX250 Hardware Manual

5.4

Installing Brackets for Cable Management

The MX250 main chassis is supplied with two

optional

plastic brackets for cable management.

Cable management on the MX250, requires the installation of the plastic brackets on the rear side

of the chassis. The plastic brackets cannot be installed on the front side of the MX250 chassis.
Follow these instructions for proper installation of the plastic brackets for cable management:

From the right side of the rear face, remove the M4 screw from position A in figure 5-2.

Hold a plastic bracket for cable management against the chassis with the plastic fingers

pointing away from the chassis and the countersunk holes on the outside. Ensure the holes

on the plastic bracket are aligned with the holes at positions A and B on the chassis.

Screw the plastic bracket into place using two M4x6 screws (58-20002-00) at positions A and

B on the chassis.

Install the other plastic bracket by repeating steps 1 to 3 for the left side of the rear panel.

Tool

Purpose

manual screwdriver, Phillips or crosshead,

sized to fit M3 screwhead

to fasten the modules into the MX250

manual screwdriver, Phillips or crosshead,

sized to fit M4 screwhead

to fasten the mounting brackets and cable

management brackets to the sides of MX250 chassis

manual screwdriver, Phillips or flat-head,

sized to fit 12-24 screws

to loosely screw in place mounting screws of chassis

to rack

power screwdriver, Phillips or flat-head,

sized to fit 12-24 screws

to tighten mounting screws of chassis to rack

manual screwdriver, Phillips or flat-head,

sized to fit M6 screws

to loosely screw in place mounting screws of chassis

to rack

power screwdriver, Phillips or flat-head,

sized to fit M6 screws

to tighten mounting screws of chassis to rack

ESD-preventative wrist strap

to prevent harmful electrostatic discharge onto

electronic equipment during installation

Figure 5-1

Required Tools for Installation

Figure 5-2

Cable Management for Mounting from Front or Middle

Summary of Contents for MX250































































Search results

Summary of Contents for MX250

Reviews:

Related manuals for MX250

Brands by name

Popular brands

Zultys MX250, Hardware Manual

Search results

Summary of Contents for MX250

Reviews:

Related manuals for MX250

Brands by name

Popular brands