background image

09

INSTALLATION INSTRUCTIONS & USER MANUAL 

804428UK V1.03  OCT 2017 - ZIP EP HYDROTAP

TECHNICAL SUPPORT

 TEL: 0345 6 005 005 EMAIL: SERVICE@ZIPINDUSTRIES .CO.UK  

WWW.ZIPWATER.CO.UK

BEFORE INSTALLATIONS

 

Before installation ensure that the following have been  

provided at the installation site

• 

Review of all the technical specifications.

• 

Ensure the under counter cupboard floor can support the product weight when full 

of water (allow an extra 2Kg when full).

• 

Sufficient space in the cupboard to install the Command Centre and other 

components in accordance with these installation instructions. See technical 

specification, page 8 for dimensions. See sections 2 to 3, pages 11 to 14 for 

installation instructions. 

• 

For all Zip HydroTap models 1 x 220-240V AC 13A socket will be required.  

  

• 

The Command Centre must be installed in accordance with IEE regulations. See 

Technical specification, page 8 for power ratings.

Note 

Check all cable and hose lengths against inlet /outlet  positions before 

proceeding (see sections 2 to 3, pages 11 to 14 for general layout).

• 

A wholesome water supply connection with isolating valve inside the cupboard 

within reach of the braided hoses (Celsius models) and positioned so that the 

connection point and the stop cock will not be obstructed when the Command 

Centre is installed. 

• 

Extra space for external filtration system. 

• 

A potable cold water supply with a minimum working pressure of:  

(see page 8 min. / max. water supply pressure).  

• 

For the Celsius range, an external hot water supply will also be required.

• 

The 0.5 MPa (5 bar) pressure limiting valve (supplied) must be fitted.

• 

The appliance must be placed with its base in a horizontal position. 

IMPORTANT! 

 Do not proceed with the installation if these requirements are not met.

!

!

Summary of Contents for HYDROTAP 2500UK

























Reviews: