background image

06

INSTALLATION INSTRUCTIONS & USER MANUAL 

804428UK V1.03 OCT 2017 - ZIP EP HYDROTAP

TECHNICAL SUPPORT

 TEL: 0345 6 005 005 EMAIL: SERVICE@ZIPINDUSTRIES .CO.UK  

WWW.ZIPWATER.CO.UK

IMPORTANT SAFETY INSTRUCTIONS

This manual contains important safety and installation instructions for the Zip HydroTap. 

Please read all warnings, installation requirements and installation instructions before 

installing any Zip HydroTap. This system must be installed in accordance with water 

supply byelaws, current IEE regulations and relevant local authority byelaws.

Safety

This appliance is not intended for use by children under 8 years. Or persons (including 

children under 8 years) with reduced physical, sensory or mental capabilities, or lack 

of experience and knowledge, unless they have been given supervision or instruction concerning the use of the 

appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play 

with the appliance. 

Qualifications 

If the power cable is damaged it must be repaired only by a qualified technician. To avoid hazards, all installation 

procedures must be carried out by a suitably qualified tradesperson. The power cable and power outlet must be in a 

safe visible position for connection.

Venting

 

Sometimes steam and / or boiling water may discharge through a vent outlet on the tap. If the tap is not installed 

using the font, ensure the tap body is located so the tap outlet & vent safely dispense into the sink bowl area. 

Lifting

Take care when lifting. The Command Centre may exceed safe lifting limits. If you feel this is beyond your personal 

capabilities, please seek assistance with the lift. Do not lift the Command Centre by the front cover or any of its 

connections. Refer to the technical specification, see page 8

,

 for the weight of the product.

Airflow

The Zip HydroTap

 

operates within the ambient temperature range 5ºC - 35ºC. Proper air circulation must be 

provided. The system will operate satisfactorily only if the recommended air gaps are provided. See Section 1 

Ventilation, page 10, for correct installation to prevent overheating. 

Frost protection

If the HydroTap is located where the ambient air temperature could fall below 5ºC when the heater is not in use, do 

not turn off the appliance electrically. This safeguard does not offer the same protection to the connecting pipework 

and fittings.

o

Positioning

 

It is important to ensure the Command Centre is positioned in an accessible area close to the floor level. The 

Command Centre

 

must have it’s base mounted in a horizontal position with all inlets and outlets facing up. The tap 

must be located above the Command Centre. See  Section 3, Command Centre

 

installation

Warnings

• 

  The Zip HydroTap

 

must be earthed. The resistance of the earth connection from each 

exposed metal part must be less than 1

Ω

.

• 

All installation and service work must be completed by trained and suitably qualified 

!

WARNINGS & REGULATORY INFORMATION

!

Summary of Contents for HYDROTAP 2500UK

























Reviews: