manualshive.com logo in svg

Zennio KEM, User Manual, Page: 24 / 49

Share
Download
Zennio KEM User Manual Download Page 24

 

 

 

 

KEM

 

http://www.zennio.com

 

                

Technical Support:

 

http://support.zennio.com

 

 

24 

2.3.2

 

CHANNEL X 

On this screen can be configured the options related to water channel objects. 

ETS PARAMETERISATION 

The parameters shown in each channel tab are the following: 

 

Figure 16. 

Water - Channel x 

 

Channel Description:

 the name set in this text box will be the ETS channel 

name. 

 

Flow Units

 [

L/h

 / m

3

/h

]: sets the measurement units of the channel flow object. 

 

Volume Units

 [

L

 / m

3

]: sets the measurement units of the channel consumption 

object. 

 

Include Channel in Global Calculation 

[

enabled 

/ disabled

]: if this parameter 

is enabled, channel values are included in global measurement. 

Note

: 

this  parameter  is  only  available  if  global  water  objects  have  been 

enabled in configuration tab (section 2.3.1). 

 

Flow  Sensor  Type 

[

Zennio

 

1/2”  Flow  Sensor 

/  Zennio  3/4”  Flow  Sensor  / 

Custom  Flow  Sensor

]:  determines  the  type  of  sensor  used  for  flow 

measurement. If "Custom Flow Sensor" is selected, the following parameters 

appear: 

Summary of Contents for KEM


















































Reviews:

No comments