30
ZCM3821-001_v01
If several beverages with milk have been prepared, the milk system
should subsequently be cleaned. Otherwise, the program will request
cleaning after the appliance is switched off and then back on again. Other
beverages will not be able to be selected.
The outlets on the outlet unit must also be cleaned of milk residues after a milky coffee
speciality has been prepared.
EMPTYING THE WASTE CONTAINER (GROUNDS BOX)
The following appears on the display:
As soon as you are prompted to empty the waste container, no more coffee can be
dispensed.
This display appears after at least 6 or at the latest 14 coffees have been dispensed.
The maximum permitted number of dispensed coffees depends on various different
settings (grinding fineness, ground coffee quantity, single/double cup).
●
Push the coffee dispensing unit into the uppermost position.
●
Open the door with the coffee outlet unit by pulling it up on the left side.
●
Pull the coffee grounds container out and clean the container thoroughly to prevent
formation of mould. Insert the cleaned waste container back into the machine and
push it until it stops.
●
Close the door with the coffee outlet.
The coffee machine is now ready to dispense coffee again.
Only empty the waste container when the coffee machine is switched on.
The coffee machine can only detect emptying when it is switched on. If you
empty the waste container with the coffee machine switched off, this will
not be detected. This may result in prompting to empty after dispensing
the first coffee when the coffee machine is switched on again the next
time.
Generally, the waste container should be cleaned daily if the coffee
machine is used every day. You will be reminded of this each time by the
following display symbol:
REMOVING AND CLEANING THE COFFEE DISPENSING UNIT
To clean the coffee dispensing unit, proceed as follows:
●
Push the coffee dispensing unit into the uppermost position.
●
Open the door with the coffee outlet unit by pulling it up on the left side.
●
Release the distribution hose on the door by pulling it lightly from the inside of the door
towards the outside
2
and pressing to the left
3
so that it clicks out of the fastener. The
dispensing unit can now be removed and the interior is easily accessible.
●
Thoroughly clean the coffee dispensing unit from the inside and outside with warm
water and a suitable brush to remove any coffee residue and prevent mould from
forming.
Disconnect and clean the hose distribution system of the coffee
dispensing unit (only if necessary, e.g, clogging), see section “CLEANING
THE HOSE DISTRIBUTION SYSTEM”.
●
Reinsert the coffee dispensing unit, see section “INSTALLING THE COFFEE
DISPENSING UNIT”.
CLEANING THE HOSE DISTRIBUTION SYSTEM
●
Grip the loose hose end near to the spring and pull the cross-shaped hose connector
1
out of its fixing. Subsequently pull both hose ends with the sleeve ends out of the
dispensing tubes
2
.
●
Pull the sleeves out of the hoses
A
and disconnect the hoses from the connecting
piece
C
. Pull the hose together with the spring
C
from the connecting piece.
●
Leave the parts immersed in a milk cleaning solution for several hours. Refer to the
instructions on the cleaning solution for the exact quantity.
●
Subsequently clean the parts with the solution and rinse them thoroughly with clean
water.
●
Push the hoses onto the connecting piece
B
and the sleeves into the hoses
A
. Insert
the hose with the spring push the hose and spring auf onto the connector
C
.
The spring must be evenly pulled over the half of the hose and the funnel-
shaped end of the hose D must face upwards.
●
Now insert both sleeve ends (with the hoses) into the dispensing tubes
2
and press
them in until they snap in properly. Push the connecting piece into the fixing slot
1
and
subsequently push the hoses to the right and left under the frame
3
.
INSTALLING THE COFFEE DISPENSING UNIT
●
Place the coffee dispensing unit in the upper position back into the door and push the
unit slightly
1
so that it audibly snaps in once.
●
Pull the hose from the inside through the door opening
2
, press it to the right into the
holder
3
and push the funnel-shaped part of the hose back into the collar until it fits
perfectly.