Zelmer 39Z017, User Manual

Page: 28 / 32

28
GW39-008_v01
Outline and parts of the hair clipper (Fig. A)
1 Cutting head
2 Cutting length adjustment knob
3 On/OFF switch
4 LCD display
5 Battery rechargeable
6 Loading socket
7
Attachments (4-6; 10-12; 16-18; 22-24; 28-30 mm)
8 Power supply
9 Cleaning brush
10 Lubricating oil for blades
11 Comb
12 Scissors
LCD display
A
percentage charging level indicator
B
graphical battery charging level indicator
C
mains supply connection indicator
Handling and operation of hair clipper
OPERATION WITH POWER SUPPLY ADAPTOR
At first insert the adaptor plug into the device and then
insert the adapter plug into the mains supply outlet. In mains
supplied mode the device is ready for use.
LOADING ACCUMULATORS AND CORDLESS
OPERATION
Load the device minimum 16h before first usage and
when 2–3 next loadings.
Make sure the appliance is switched off before charging.
●
The process of battery (installed in the trimmer) charging
●
lasts approximately 2 hours.
The trimmer can work approx. 60 minutes with fully
●
charged batteries.
Insert the ending of the power supply to the trimmer
–
charging socket (6) ,
Insert the plug of the power supply in the mains
–
supply outlet. The percentage and graphical
charging level indicators show the charging process
advancement (flashing).
When the battery is fully charged, the LCD display
●
(4)
indicates 100 and it is highlighted in blue .
When the battery charging level decreases below 20, the
●
graphical battery charging level indicator (B) and mains
supply connection indicator (C) start flashing.
When the battery is almost empty, the display colour
●
changes into red . Connect the trimmer to the mains supply.
The hair clipper accumulator obtains optimum power
●
after three cycles of loading and unloading. Ten hours
is enough for next loading. In order to provide long life
of accumulators, they should be completely unloaded
before loading.
COMB ATTACHMENTS INSERTING / REPLACING
Select the attachment according to the length of cutting.
●
Insert appropriate attachment into the sides of the device.
●
The protrusions shall be locked inside small holes (see
the figure beside) on left and right sides.
Replace one attachment removing it and inserting
●
another as described above.
In order to remove an attachment bent one side of assembled
attachment gently and then move it up.
Move the cutting length adjustment knob
●
(2) , to increase/
reduce the hair cutting length. The possible hair cutting
length is indicated on each attachment (i.e. 4–6 mm).
USING THE TRIMMER FOR HEAR CUTTING
Cut the hair for demanded length in stages, start form
bigger length.
Insert an appropriate attachment
●
(7) .
Set the desired length of hair/beard cutting with cutting
●
length adjustment knob (2) .
Start up the hair clipper pressing in ON/OFF button
●
(3) .
Cut only small areas.
●
Move the clipper slowly along hair.
●
Hold the device so, that the comb attachment is laid flat.
●
Always start the cutting from the neck upwards or from
●
the forehead and temples upwards to the top of head.
CUTTING HAIR WITHOUT ATTACHMENT
WARNING: The cutting head (1) is very sharp. Injury
hazard!
Cutting without attachment makes possible to trim the
contour, hair line and whiskers as well as neck shaving.
Turn the device so, that the back part was directed
●
upwards.
Place the edge of the cutting head
●
(1) without comb
attachment on desired length of bristle hairline.
Move down the clipper in operation.
●
Cleaning and maintenance
Start the device pressing in ON/OFF button
●
(3) .
Always switch off the hair clipper and unplug the adaptor
●
from the mains supply outlet before cleaning and
maintenance.
Remove the comb attachment from the hair clipper.
●
In order to remove cutting head press the cutting head
●
blade (1) forward with your thumb, in order to release it
from the frame (Fig. C) .
If necessary, rinse the plastic comb attachments under
●
running water, and then dry them thoroughly.
Remove the remains of hair from the cutting head
●
(1)
with attached cleaning brush (VII) .
Insert the protrusion of cutting head
●
(1) back into the
locking hole in the frame of cutting head.
Press gently the cutting head
●
(1) in, until you hear
a clicking sound of locking.