background image

 

NOTES ON INSTRUMENT SAFETY 

 

Carl Zeiss 

General Indications 

VivaTome 

 

 
 

423639-9000-701 

M60-2-0046 e   05/2012 

1

 

NOTES ON INSTRUMENT SAFETY 

1.1

 

General Indications 

VivaTome has been designed, manufactured and tested in compliance with the standard DIN EN 61010-1 

(IEC 61010-1) "Safety Regulations for Electrical Measuring, Control and Laboratory Instruments". 
The instrument meets the requirements of the EC Directives 2006/95/EC "Low-Voltage Directive" and 

2004/108/EC "Electromagnetic Compatibility", as well as the standard DIN EN 62471 (IEC 62471) 
"Photobiological Safety of Lamps and Lamp Systems". 

It carries the 

 mark. 

The instrument has to be disposed of in compliance with the WEEE Directive 2002/96/EC. 

 

The warning and information symbols explained below will help you recognize at a glance the type and 

purpose of the notes included in this operating manual: 

 

CAUTION

 

This symbol indicates a possible hazard to the user of the instrument.

 

 

CAUTION

 

Do not look into the light source! This could cause damage to your eyes. Risk class 2 according 

to IEC 62471

 

 

CAUTION: High-energy UV radiation! 

 

Risk of damage to eyes and skin!

 

 

CAUTION

 

Disconnect the power cable before opening the instrument!

 

 

ATTENTION

 

This symbol indicates a possible hazard to the instrument or system.

 

 

NOTE

 

This symbol indicates a note containing special instructions.

 

 

 

 
Apart from the present operating manual you should observe the following operating manuals for your 
detailed information: 

 

Operating manual of VivaTome manufactured by Aurox Ltd. 

 

Operating manual of the microscope (Axio Imager, Axio Observer or Axio Examiner) 

 

Operating manual for the computer system 

 

Operating manual of the camera (AxioCam MRm, HRm or EM) 

 

Operating manual of HXP 120 C or HXP 120 

 

Summary of Contents for VivaTome

























Reviews: