YOKOGAWA WT1800E User Manual Download Page 99

Page: 99 / 154

16-5

IM WT18O1E-02EN

16.3 Configuring the Save Conditions of Stored

Numeric Data

This section explains the following settings for the save conditions of stored numeric data:
•  Save destination
•  Selecting whether to perform automatic CSV conversion when storage stops
•  Auto naming
•  File name
• Comment

►

“Save Conditions (File Settings)” in the features guide

File Settings Menu

Press

SHIFT+STORE START

(STORE SET) and then the

File Settings

soft key to display the

following menu.

Set the save destination and perform manual CSV conversion.

Set auto naming. ► section 17.2

Select whether to perform automatic CSV conversion when storage stops.

Set the file name. ► section 17.2

Set a comment. ► section 17.2

Setting the Save Destination and Performing Manual CSV

Conversion

Press the

File List

soft key to display the following screen.

Set the save destination.

When storage starts (see section 16.4), storage data is saved to the specified file

name at the specified save destination.

* You cannot specify a network drive as the save destination.

Executes the manual CSV conversion

Select the storage data file (.WTS file) that was saved, and

then press the

CSV Convert

soft key to create a storage data

file in ASCII format.

Summary of Contents for WT1800E



























































































































































Search results

Summary of Contents for WT1800E

Reviews:

YOKOGAWA WT1800E, User Manual, Page: 99 / 154

Search results

Summary of Contents for WT1800E

Reviews: