manualshive.com logo in svg

YOKOGAWA WT1800E, User Manual, Page: 150 / 154

Share
Download
YOKOGAWA WT1800E User Manual Download Page 150

App-5

IM WT18O1E-02EN

Code

Message

Chapter or Section

890

Cannot start the store.

Change store mode from synchronize with integration or set store interval to zero by 

the [STORE SET] menu.

Otherwise, turn off Auto of the Data Update Interval by the [UPDATE RATE] menu.

16.1 or 1.15

891

Cannot start the auto print.

Change print mode from sychronize with integration by the [STORE SET] menu.

Otherwise, turn off Auto of the Data Update Interval by the [UPDATE RATE] menu.

19.2 or 1.15

892

Cannot start the integration.

Set S and Q Formula to another expecting for Type 3 by the [MEASURE] menu, or fix 

measurement ranges. 

7.3, 1.2, or 1.3

System Error Messages (900 to 999)

Code

Message

Chapter or Section

901

Failed to backup setup data.

The system has been initialized.

Maintenance service is required.

—

902

System RAM failure.

Maintenance service is required.

—

903

System ROM failure.

Maintenance service is required.

—

905

System failure.

Install the input modules and the options correctly.

—

906

Fan stopped.

Power off immediately.

Maintenance service is required.

—

907

Backup battery is flat.

Maintenance service is required to replace the back-up battery.

—

909

Illegal SUM value.

Maintenance service is required.

—

910

This operation is prohibited for EEPROM protection.

—

915

EEPROM SUM error.

EEPROM may be damaged.

Maintenance service is required.

—

919

Module installation condition and setup parameters do not match.

The system has been initialized.

Maintenance service is required.

—

920

SUM error of NULL value.

The Null value is reset to 0.

—

921

System Failed to Draw Display.

Maintenance service is required.

—

922

Failed in communication with devices.

Maintenance service is required.

—

923

Transmit data abnormality from devices.

Maintenance service is required.

—

926

The USB device’s power consumption exceeded the capacity of the USB hub.

—

927

Disconnected USB device port 1, because overcurrent was detected.

—

928

Disconnected USB device port 2, because overcurrent was detected.

—

929

A USB mass storage device that is greater than 137 GB in capacity has been 

connected.

Be careful in using this device.

If an area exceeding 137 GB is accessed, the storage device may break.

—

931

Hardware configuration error occurred. Restart this machine.

If it occurred again, maintenance service is required.

—

932

Error occurred while ImageFile process. 

—

Appendix 1  Messages and Corrective Actions

Summary of Contents for WT1800E



























































































































































Reviews:

No comments