YOKOGAWA WT1800E User Manual Download Page 143

Page: 143 / 154

21-9

IM WT18O1E-02EN

21.8 Performing Zero-Level Compensation

This section explains how to perform zero-level compensation.

►

“Zero-Level Compensation (CAL)” in the features guide

Press

SHIFT+SINGLE

(CAL) to execute zero-level compensation.

Note

• This instrument automatically performs zero-level compensation after you change the measurement

range or input filter.

• To make accurate measurements, we recommend that you execute zero-level compensation after

warming up the instrument for at least 30 minutes.

• If the measurement range and input filter remain the same for a long period of time, the zero level may

change due to the changes in the environment. If this happens, we recommend that you execute zero-
level compensation.

• The integration feature includes an auto calibration feature that automatically performs zero-level

compensation.

Summary of Contents for WT1800E



























































































































































Search results

Summary of Contents for WT1800E

Reviews:

YOKOGAWA WT1800E, User Manual, Page: 143 / 154

Search results

Summary of Contents for WT1800E

Reviews: