YETI SNOWMX USER MANUAL
|
24
• Cracks
: Visually inspect the System’s frame
and Bike Mount for cracks or defects that can
impair proper operation of the System.
•
Bike Mount - Lubrication
: Lube the Bike
Mount’s moving parts. Refer to “Lubrication” in
the
Maintenance
section on page 28.
•
Bike Mount - Adapters
: Check for play at
points where the rear System mounts to the
bike. Refer to “Wear” in the
Maintenance
section
on page 34.
Track
•
Tension
: Set or check track tension on the
System according to the manufacturer’s
recommendations. Refer to “Rubber Track
Tension” in the
Adjustments
section on page 21.
•
Wear
: Verify wear and overall condition of the
System’s rubber track. Refer to “Wear” in the
Maintenance
section on page 30.
CAUTION: A damaged track can result in premature
wear on suspension components.
Wheels
•
Wear
: Verify general condition of wheels and
inspect for wear on the outside diameter or
deformation. Refer to “Wear” in the
Maintenance
section on page 31. Replace wheel(s) if a defect
is present.
•
Bearings
: Check wheel bearings for restriction,
noise or abnormal play in rotation. Replace
wheel bearing if it shows any one of these
defects.
Suspension
•
Track Guides - Wear
: Inspect for wear on
Suspension Guide rails. Refer to “Wear” in the
Maintenance
section on page 31. Replace guide
rails if wear is too great.
•
Front Suspension Arm - Lubrication
: Lube
the front suspension arm’s upper pivot shaft and
lower nylon bushings as per the maintenance
chart. Refer to “Lubrication” in the
Maintenance
section on page 27.
•
Front Suspension Arm - Cracks
: Visually
inspect front suspension arm for cracks or
defects that can impair proper operation.
•
Shock Absorbers Upper & Lower Mounting
Points - Lubrication
: Lube the shock absorbers’
upper and lower mounting points as per the
maintenance chart. Refer to “Lubrication” in the
Maintenance
section on page 27.
•
Shock Absorbers Lower Mounting Points -
Wear
: Check the shock absorbers’ lower
mounting point bushings for wear. Replace
parts, if bore in bushings becomes oval or there
is excessive play. Refer to “Wear” in the
Maintenance
section on page 31.
•
Nylon Bushings - Wear
: Verify play and extent
of wear of nylon bushings on front and rear
suspension arm. Refer to “Wear” in the
Maintenance
section page 32. Replace bushings
if play or wear is too great.
•
Drive Sprockets - Wear
: Inspect for wear on the
sprockets driving the rubber track. Refer to
“Wear” in the
Maintenance
section on page 30.
Replace the sprockets if wear is too great.
•
Rubber Dampers
: Check general condition of
rubber dampers on suspension rails. Refer to
“Wear” in the
Maintenance
section on page 32.
Replace dampers if they are severely deformed
or cracked.
Ski
•
Ski Skag
: Inspect general condition of Skag.
Refer to “Wear” in the
Maintenance
section on
page 32. Replace Skag if it shows signs of
damage or deformation.
•
Side Runners
: Inspect general condition of the
ski’s Side Runners. Refer to “Wear” in the
Maintenance
section on page 33. Replace Side
Runners if they show signs too much wear or
deformation.
•
Rubber Damper
: Inspect general condition of
the Rubber Damper located on the ski. Replace
damper if it is deformed, cracked or shows
severe wear. Refer to “Wear” in the
Maintenance
section on page 33.
Spindle
•
Nylon Bushings - Wear
: Verify play and extent
of wear of nylon bushings on bolt securing ski to
spindle. Refer to “Wear” in the
Maintenance
section on page 33. Replace bushings if play or
wear is too great.
