Yealink Yealink SIP-T48G Administrator'S Manual Download Page 59

Page: 59 / 319

Getting Started

Parameter:

network.bridge_mode

Configure network parameters of
the PC port.

Parameter:

network.pc_port.ip

network.pc_port.mask

network.pc_port.dhcp_server

network.dhcp.start_ip

network.dhcp.end_ip

Local

Web User Interface

Configure the PC port mode.

Configure the PC (LAN) port type.

Configure network parameters of
the PC port.

Navigate to:

http://<phoneIPAddress>/servlet
?p=network-pcport&q=load

Details of Configuration Parameters:

Parameters

Permitted Values

Default

network.pc_port.enable

0 or 1

Description:

Enables or disables the PC (LAN) port.

0-Disabled

1-Auto Negotiation

Note: If you change this parameter, the IP phone will reboot to make the change take
effect.

Web User Interface:

Network->PC Port->PC Port Active

Phone User Interface:

None

network.bridge_mode

0 or 1

Description:

Configures the PC (LAN) port type.

Summary of Contents for Yealink SIP-T48G
































































































































































































































































































































Search results

Summary of Contents for Yealink SIP-T48G

Reviews:

Yealink Yealink SIP-T48G, Administrator'S Manual, Page: 59 / 319

Search results

Summary of Contents for Yealink SIP-T48G

Reviews: