Yealink Yealink SIP-T48G Administrator'S Manual Download Page 180

Page: 180 / 319

Microsoft Lync Edition Administrator’s Guide for SIP-T2_Series and T4_Series IP Phones

168

network.snmp.enable

network.snmp.port

network.snmp.trust_ip

Local

Web User Interface

Configure SNMP on the IP
phone.

Navigate to:

http://<phoneIPAddress>/servl
et?p=network-adv&q=load

Details of Configuration Parameters:

Parameters

Permitted Values

Default

network.snmp.enable

0 or 1

Description:

Enables or disables SNMP (Simple Network Management Protocol) feature on the
IP phone.

0-Disabled

1-Enabled

Note: If you change this parameter, the IP phone will reboot to make the change
take effect. It is only applicable to SIP-T48G IP phones.

Web User Interface:

Network->Advanced->SNMP->Active

Phone User Interface:

None

network.snmp.port

Integer from 1 to

65535

161

Description:

Configures the port used for SNMP (Simple Network Management Protocol)
communication.

Note: If you change this parameter, the IP phone will reboot to make the change
take effect. It is only applicable to SIP-T48G IP phones.

Web User Interface:

Network->Advanced->SNMP->Port (1~65535)

Phone User Interface:

None

Summary of Contents for Yealink SIP-T48G
































































































































































































































































































































Search results

Summary of Contents for Yealink SIP-T48G

Reviews:

Yealink Yealink SIP-T48G, Administrator'S Manual, Page: 180 / 319

Search results

Summary of Contents for Yealink SIP-T48G

Reviews: