Yealink Yealink SIP-T48G Administrator'S Manual Download Page 313

Page: 313 / 319

Appendix

301

User A mixes the RTP channels and establishes a conference between User B and
User C.

F9. INVITE(sendonly)

F10. INVITE (sendonly)

F15. INVITE C

F11. 200 OK

F12. 200 OK

F1. INVITE B

F2. INVITE B

F3. 180 Ringing

F4. 180 Ringing

F5. 200 OK

F6. 200 OK

F7. ACK

F8. ACK

Session1 established between User A and User B is active

F13. ACK

F14. ACK

Session 1 established between User A and User B is hold

F16. INVITE C

F18. 180 Ringing

F17. 180 Ringing

F19. 200 OK

F20. 200 OK

F21. ACK

F22. ACK

Both calls are active, come into three-party conference

User A

Proxy Server

User B

User C

Initiate

three party

conference

Step

Action

Description

INVITE—User A to Proxy
Server

User A sends the INVITE message to a
proxy server. The INVITE request is an
invitation to User B to participate in a
call session.

In the INVITE request:



The IP address of User B is inserted
in the Request-URI field.

Summary of Contents for Yealink SIP-T48G
































































































































































































































































































































Search results

Summary of Contents for Yealink SIP-T48G

Reviews:

Yealink Yealink SIP-T48G, Administrator'S Manual, Page: 313 / 319

Search results

Summary of Contents for Yealink SIP-T48G

Reviews: