manualshive.com logo in svg

Yealink Yealink SIP-T48G, Administrator'S Manual, Page: 183 / 319

Share
Download
Yealink Yealink SIP-T48G Administrator'S Manual Download Page 183

Configuring Advanced Features

 

171

 

DNS server) for the IP phone can be statically configured by an administrator. 

 

Stateless Address Autoconfiguration (SLAAC): SLAAC is one of the most convenient 
methods to assign IP addresses to IPv6 nodes. SLAAC requires no manual 
configuration of the IP phone, minimal (if any) configuration of routers, and no 
additional servers. To use IPv6 SLAAC, the IP phone must be connected to a 
network with at least one IPv6 router connected. This router is configured by the 
network administrator and sends out Router Advertisement announcements onto 
the link. These announcements can allow the on-link connected IP phone to 
configure itself with IPv6 address, as specified in RFC 4862. 

 

Stateful DHCPv6: The Dynamic Host Configuration Protocol for IPv6 (DHCPv6) has 
been standardized by the IETF through RFC3315. DHCPv6 enables DHCP servers to 
pass configuration parameters such as IPv6 network addresses to IPv6 nodes. It 
offers the capability of automatic allocation of reusable network addresses and 
additional configuration flexibility. This protocol is a stateful counterpart to “IPv6 
Stateless Address Autoconfiguration”, and can be used separately or in addition to 
the stateless autoconfiguration to obtain configuration parameters. 

Note 

Procedure

 

IPv6 can be configured using the configuration files or locally. 

Configuration File 

<MAC>.cfg 

Configure the IPv6 address 
assignment method. 

Parameters: 

network.ip_address_mode 

network.ipv6_internet_port.type 

network.ipv6_internet_port.ip 

network.ipv6_prefix 

network.ipv6_internet_port.gateway 

network.ipv6_icmp_v6.enable 

Configure the IPv6 static DNS 
address. 

Parameters: 

network.ipv6_primary_dns 

network.ipv6_secondary_dns 

<y0000000000xx>.c

Configure the IPv6 static DNS. 

Stateful DHCPv6 address assignment method feature is only applicable to SIP-T48G IP 
phones. 

If the IP phone enables the SLAAC and DHCPv6 features simultaneously, the IP phone will 

obtain the IP address via SLAAC and obtain other network parameters via DHCPv6. 

Summary of Contents for Yealink SIP-T48G
































































































































































































































































































































Reviews:

No comments