manualshive.com logo in svg

Yealink Yealink SIP-T48G, Administrator'S Manual, Page: 167 / 319

Share
Download
Yealink Yealink SIP-T48G Administrator'S Manual Download Page 167

Configuring Advanced Features

 

155

 

Parameters 

Permitted Values 

Default 

Discovery Protocol) request. 

Note: It works only if the value of the parameter “network.cdp.enable” is set to 1 
(Enabled). If you change this parameter, the IP phone will reboot to make the 
change take effect.   

Web User Interface:   

Network->Advanced->CDP->Packet Interval (1~3600s) 

Phone User Interface: 

None 

To configure CDP via web user interface: 

1.

 

Click on Network->Advanced. 

2.

 

In the CDP block, select the desired value from the pull-down list of Active. 

3.

 

Enter the desired time interval in the Packet Interval (1~3600s) field. 

 

4.

 

Click Confirm to accept the change. 

A dialog box pops up to prompt that settings will take effect after a reboot. 

5.

 

Click OK to reboot the phone. 

VLAN is disabled on IP phones by default. You can configure VLAN for the Internet port 
and PC port manually. Before configuring VLAN on the IP phone, you need to obtain the 
VLAN ID from your network administrator. 

Procedure

 

VLAN can be configured using the configuration files or locally. 

Configuration 

<y0000000000xx>.cfg 

Configure VLAN for the Internet port 

Summary of Contents for Yealink SIP-T48G
































































































































































































































































































































Reviews:

No comments