13
O R I G I N A L I N S T R U C T I O N S
GB
CHARACTERISTICS OF TOOL
Petrol hedge shear is intended only for trimming and forming shrub crowns and trimming of thin twigs. Thanks for the petrol drive
it retain greater mobility than electric shear. Correct, reliable, and safe operation of the device is dependent on its proper use,
therefore:
Prior to working with the device, you should read all the instruction and keep it around.
For any damage or injuries caused by the tool misuse, failure to comply with safety regulations and instructions of this manual, the
supplier is not responsible. The tool misuse causes also the loss of user rights to the guarantee and warranty.
EQUIPMENT
The shear is supplied in a complete state and requires no assembly.
TECHNICAL DATA
Parameter
Unit
Value
Catalog number
YT-85021
Weight (without fuel)
[kg]
5.8
Fuel tank capacity
[l]
0.6
The length of cutting
[mm]
550
The length of guide bar
[mm]
610
Maximum cutting thickness
[mm]
34
Cutting speed
[min
-1
]
1850
Engine
the number of cylinders
1
the number of strokes
2
cooling
air
Spark plug type
L8RTF
Engine displacement
[cm
3
]
25.4
Engine power
[kW]
0.70
Maximum rotation speed of the engine
[min
-1
]
9500
The maximum recommended engine speed with the cutting unit
[min
-1
]
7000
Recommended idling speed
[min
-1
]
3400
Fuel consumption at max. engine power
[kg/h]
0.367
Noise - pressure L
pA
[dB (A)]
96 ± 3
Noise - power L
pA
[dB (A)]
105,3 ± 0,48
Level of vibration
[m/s
2
]
6.9 ± 1.5
SAFETY INSTRUCTIONS
IMPORTANT. Read carefully before starting the shear operation. Keep for future use.
Every time when in the description appears the term: “device” it should be treated as a “hedge shear”.
PREPARATION
THE DEVICE MAY BE THE CAUSE OF SERIOUS INJURY. Carefully read the instructions manual. Become familiar with the cor-
rect handling, operation, maintenance, starting and stopping the device. Become familiar with the correct handling of all controls.
Never allow children to operate the device.
Be careful during cutting the live wires, both above-ground and overhead.
Do not work with scissors, if there are bystanders, especially children. Before starting thework you should assign a safety zone
with a radius of at least 5 metres away from the place of work.
Always wear eye and face shields, it protects your eyes, face and respiratory tract against dust, exhaust, and pieces of wood
arising while cutting. Always wear the appropriate, fitting to the body, protective clothing. Do not wear loose clothing or jewelry,
because it can be caught by moving parts of the tool. Wear protective gloves and hearing protection. Wear safety shoes with
non-slip soles.
Take special care when handling fuel. It is flammable, and its vapors are explosive. Please observe the following recommenda-
tions.
- Only use canisters, which are designed for the fuel.
- Never remove the fuel filler cap nor add fuel when the engine is running. Before tanking wait until the engine and the exhaust
Summary of Contents for YT-85021
