11
GB
O R I G I N A L I N S T R U C T I O N S
PROPERTIES OF THE TOOL
The impact wrench is a versatile tool, that does not require an external power source, it is portable, designed for the DIY users. It
should be used only for is crewing in and out bolts and nuts with left-hand and right-handed thread, by using a variety of screw-
driver bits. Through the impact mechanism the impact wrench o
ff
ers much higher torque than a typical cordless screwdriver drill.
Its special advantages would be appreciated by the DIYs who make a variety of assembly and
fi
nishing works. A correct, reliable
and safe functioning of the electric tool depends on its proper use, so:
Before you proceed to operate the device, read the manual thoroughly and keep it.
The supplier will not be held responsible for any damage resulting from the safety regulations and the recommendations indicated
hereby not being observed.
EQUIPMENT
The product is supplied in a complete state and requires no assembly. Together with the product there are provided: the recharge-
able battery and charging station (charger).
TECHNICAL PARAMETERS
Parameter
Unit of measurement
Value
Catalogue number
YT-82802
Operating voltage
[V]
18 DC
Rotation (idle)
[min
-1
]
0 - 1600 / 0 - 2600
Impact frequency
[min
-1
]
0 - 4400
Maximum torque
[Nm]
180 / 250
Noise level
- acoustic pressure
[dB]
86,0 ± 3,0
- LWA power
[dB]
97,0 ± 3,0
Protection grade
IPX0
Insulation class
III
Level of vibration (drilling / screwdriveting)
[m/s
2
]
7,58 ± 1,5
Mass
[kg]
1,3
Tool handle
[”/mm]
1/2 / 12,5
Battery
Li-Ion
Capacity of the battery
[Ah]
3
Charger
Input voltage
[V]
220 - 240
Mains frequency
[Hz]
50 / 60
Rated power
[W]
50
Output voltage
[V]
21,4 DC
Input current
[A]
2
Time of charging**
[h]
1,5
** charging time applies only to the battery with a capacity listed in table
GENERAL WARNINGS FOR THE SAFETY OF POWER TOOLS
Warning! Read all safety warnings, illustrations and speci
fi
cations provided with this power tool.
Failure to do so may
result in electric shock,
fi
re or serious injury.
Keep all warnings and instructions for future reference.
The term “power tool” used in warnings applies to all tools driven by power both wired and wireless.
Workplace safety
Keep the workplace well-lit and clean.
Disorder and poor lighting can be causes of accidents.
Do not work with power tools in an environment with an increased risk of explosion, containing
fl
ammable liquids, gases
or vapors.
Power tools generate sparks that can ignite dust or fumes.
Children and third persons should not be allowed to enter the workplace.
Loss of concentration can result in loss of control.
Summary of Contents for YT-82802
