Bump
Knob
Inner
Reel
Spool
Spring
3"-4"
IMPORTANT: READ OPERATOR’S MANUAL THOROUGHLY AND FOLLOW THE SAFE OPERATION PRACTICES WHILE OPERATING THE UNIT.
Remove Unit From Carton
Assemble The Unit
Start The Unit
Place
shield
onto
mount
bracket
. Securely screw
2
shield
screws
through holes on mount
bracket and into shield. Make
sure screws are tightened equally
so there is an equal gap between
bracket and shield on each side.
Put handle on shaft. Move
handle a
minimum 6 inches
away from shaft grip. Insert
bolt and tighten.
Assemble The Unit
Mix thoroughly in separate
fuel can:
– 3.2 fl. oz. of 2-cycle
engine oil
– 1 gallon of unleaded
gasoline
NOTE:
Do not mix directly in
fuel tank.
Place unit on a level surface
and fill fuel tank.
DO NOT
overfill.
Press
primer bulb
10 times
,
or until fuel is visible
Crouch in starting position.
SQUEEZE
and
HOLD
throttle for
ALL
further
steps.
Pull
rope
5 times
.
Move
choke lever to
Position 2
and squeeze
throttle.
Pull
rope
3-5 times
to start
engine.
Run
unit for
30-60
seconds
to warm up.
Continue to squeeze
throttle.
Move
choke lever
to
Position 3
.
1
1
2
Remove all contents from
the carton.
4
5
6
1
8
9
3
Move
choke lever to
Position 1
.
Continue to squeeze
throttle.
Run
unit for an
additional 60 seconds
to
complete warm-up. Unit
may be used during this
time.
7
Start The Unit
10
11
12
13
14
Primer
Bulb
10 X
5 X
3-5 X
Choke Lever
DIDN’T START?
IF
engine doesn’t start, go back to step 6.
IF
engine fails to start after 2 attempts, move
choke lever to position 3 and pull the starter
rope until engine starts.
IF
engine hesitates, return choke to Position
2 and continue to warm-up.
NOTE
: unit is properly warmed up when
engine accelerates without hesitation.
1 Gallon
3.2 oz
40:1
Choke Lever
Choke Lever
Unscrew bump knob
counterclockwise. Remove
inner reel and spring.
Insert 10'
of
0.080"
SplitLine
®
through hole in top
of reel. Pull most of line
through hole until 3"-4"
remains.
Bend short end and push it
into the other hole. Pull tight.
Wind line tightly in direction
of arrow. Split other end of
SplitLine
®
back 6"-7".
Push 6"-7" ends into 0.080"
holding slots.
Insert or slide lines into the
eyelets in spool. Insert spring
and reel into spool.
1
1
2
Pull lines firmly to release
from holding slots.
Reload The Line*
3
4
5
6
7
Hold the inner reel in place.
Tighten Bump Knob
clockwise.
1
8
Reload The Line
Replacement SplitLine
®
:
Part #49U2134K953
For single line installation
, refer to Line Installation
section of this manual.
For replacement spool installation
, refer to
Installing a Prewound Reel section of this manual.
*This is to assist in the reloading of Splitline® only. These instructions
are NOT part of the fast assembly instructions. Line does not need to
be installed on the initial assembly and start-up.
Tools Required:
• #2 Phillips screwdriver
Min. 6"
Starter Rope
Fuel Cap
Throttle Control
On/ Off Switch
D-Handle
Cutting Head Shield
Primer Bulb
Choke Lever
Spark Plug
Cutting Head
Air Filter Cover
Y60
2-Cycle Trimmer
Operator’s Manual
769-07118 P00
04/11
NEED HELP?
Call 1-800-800-7310 in U.S. or 1–800–668–1238 in Canada
ENGLISH — P
AGE 1
FRANÇAIS — P
AGE 5
ESP
AÑOL — P
AGE 9
