Yamato WG270 Instruction Manual Download Page 8

Page: 8 / 71

４

2. Before Using this unit

Requirements for Installation

WARNING!

1. Be sure to connect grounding wire.



Always connect the equipment to the ground. If the equipment is not grounded, ground

leakage, if any, may not activate the ground leakage breaker, resulting in
extremely-hazardous electric shock.



Connect the grounding wire either to the grounding wire or grounding terminal block of the

electric power equipment. If the grounding equipment is not available, consult the nerest
electric constructor and carry out grounding according to Article 18 (Type III Grounding Work
of 100

or less) of the Technical Standards for Electric Equipment.



Never connect the grounding wire to gas pipe or water supply pipe.

2. Choose a proper place for installation



Do not install this unit in a place where:



Rough or dirty surface.



Flammable gas or corrosive gas is generated.



Ambient temperature 35



C and above or 5



C and below.



Ambient temperature fluctuates violently.



There is direct sunlight.



There is excessive humidity and dust.



There is a constant vibration.



Not horizontal surface.



The power source is instable.

Keep space around each product above the range shown below.
Install units within sink equipment if possible.

10 ㎝ or

Summary of Contents for WG270








































































Search results

Summary of Contents for WG270

Reviews:

Yamato WG270, Instruction Manual, Page: 8 / 71

Search results

Summary of Contents for WG270

Reviews: