Yamato WG270 Instruction Manual Download Page 11

Page: 11 / 71

７

2. Before Using this unit

Requirements for Installation

WARNING!

9. Observe the specified pressure range of raw water from waterworks



Apply the range of city water pressure between 0.5 - 5 X 100kPa (0.5 - 5kgf/cm

) including

nighttime.



Range of raw water pressure is the same when "Water Supply Port Unit" (optional

accessory) is used.

10. Connect the water supply hose securely



Take the supply hose (with connection port) out of attachments Install the unit on a

horizontal and stable place nearby tap and sink.



If not connecting the water supply hose securely, the water supply hose or connection port
may be disconnected, resulting in water leakage such as water bursting forth.

11. Connect the tap side

1. Slide the sleeve of socket

③

on connection port side in the arrow direction, then

connection port body and water supply hose can be separated. There separate the two
parts.

2. Once loosen the plug

②

from the ring

①

3. Tighten the 4 mounting screws

⑤

uniformly while pressing the ring

①

slightly and

uniformly to make the packing

⑥

in flat contact with water tap. If the tap is a chemical

tap, adjust the position so that the mounting screw is located at the bottom valley of tap
nipple as shown.

4. Turn the plug

②

clockwise to tighten securely. This will allow the tap and connection port

to be sealed by packing

⑥

5. Insert the socket

③

securely to the plug

②

with the sleeve slid in the arrow direction.

The sleeve returns to the original position when released, and then connection is
completed.

* In case that the socket is removed, the valve attached on the connection side of the main

unit stops the flow of water.

Tap

Connection

port body

Socket on
connection

port side

Water

supply hose

Water supply port

Sleeve on water

supply side

④

Tap

⑤

⑥

⑦

①

②

③

Sleeve

Water supply

hose

Connection Port Body

①

Ring

②

Plug

③

Socket

④

Spacer

⑤

Mounting Screw

⑥

Packing

⑦

Filter

One-touch
Joint

Summary of Contents for WG270








































































Search results

Summary of Contents for WG270

Reviews:

Yamato WG270, Instruction Manual, Page: 11 / 71

Search results

Summary of Contents for WG270

Reviews: