Yamato Pure Line WE200 Instruction Manual Download

Page: 38 / 55

6. MAINTENANCE PROCEDURES

Ion Exchange Resin Cartridge Replacement

For replacement procedure, see

“Install the ion exchange resin cartridge” (P.11). Notification alarm will

automatically reset once water quality improves, following cartridge replacement.

・

Degraded water quality and processing capacity will be exhibited from cartridges stored for an extended

time period. Discretion is therefore advised in preparing spare cartridges. Cartridge shelf life is

approximately 4 months.

・

Spent cartridges should be discarded as non-combustible material or returned to Yamato (applicable in

Japan only). Use the mailing label supplied with cartridge for returns. Yamato Scientific promotes

collection and recycling for preservation of the environment.

・

Following cartridge replacement, discard the first 4

ℓ

of water dispensed to purge system of air and initial

impurities.

Pre-process Cartridge Replacement

For replacement procedure, see

“8. Install the pre-process cartridge” (P.12). To reset notifications/alerts, see

“How to reset after replacement of consumable parts” (P.36).

・

Ion exchange resin cartridge life will shorten if unit is used without replacing the pre-process cartridge at

specified interval.

・

Spent cartridges should be discarded as non-combustible material or returned to Yamato (applicable in

Japan only). Use the mailing label supplied with cartridge for returns. Yamato Scientific promotes

collection and recycling for preservation of the environment.

Reverse Osmosis (RO) Membrane Replacement

To replace, see

“13. Install the reverse osmosis (RO) membrane.

To reset notifications alerts, see

“Wear Item Replacement Alert Reset” (P.36). Running Initial wash and

adjusting the pressure calibration valve must be done after replacing RO membrane. For initial wash pressure

calibration procedures, see

“Run initial wash for reverse osmosis membrane” (P.16) and “15. Calibrate

pressure for reverse osmosis membrane.

(P.17).

・

Ion exchange resin cartridge life is shortened and specified water quality and/or sample size will not be

accurate if RO membrane is not replaced at specified interval.

・

Spent cartridges should be discarded as non-combustible material.

Summary of Contents for Pure Line WE200
























































Search results

Summary of Contents for Pure Line WE200

Reviews:

Related manuals for Pure Line WE200

Brands by name

Popular brands

Yamato Pure Line WE200, Instruction Manual

Search results

Summary of Contents for Pure Line WE200

Reviews:

Related manuals for Pure Line WE200

Brands by name

Popular brands