Yamato Pure Line WE200 Instruction Manual Download

Page: 27 / 55

4. OPERATION PROCEDURE

Ion Exchange Water Sampling Procedure

Sampling ion exchange water

①

Press POWER.

●

Water quality appears in the water quality

display

②

Ion exchange water may be sampled by

pressing PUSH. Sample will not stop

dispensing after releasing key.

●

“In-operation” lamp illuminates and

information

display

shows

sample

dispensing progress.

Sample dispensing progress:

※

Quality of water remaining in system

deteriorates if sample is not taken within

a certain timeframe. While confirming

quality in the display, draw sample until

water purity improves.

②

Pressing

PUSH

once

stops

dispensing ion exchange water sample.

●

“In-operation” lamp goes out.

●

Sample

dispensing

progress

stops

showing in information display.

※

Sample may take a moment to begin dispensing from newly purchased unit or from unit on

which a wear item has just been replaced, due to air in the system.

Summary of Contents for Pure Line WE200
























































Search results

Summary of Contents for Pure Line WE200

Reviews:

Related manuals for Pure Line WE200

Brands by name

Popular brands

Yamato Pure Line WE200, Instruction Manual

Search results

Summary of Contents for Pure Line WE200

Reviews:

Related manuals for Pure Line WE200

Brands by name

Popular brands