Yamato Pure Line WE200 Instruction Manual Download Page 17

Page: 17 / 55

2. PRE-OPERATION PROCEDURES

Installation

13. Install the reverse osmosis (RO) membrane.

●

urn power off and close water tap before installing or replacing the reverse osmosis

(RO) membrane.

●

WE200 unit is shipped with an RO membrane installed. Review the following when
replacing.

●

Install procedure:

(1) Place RO membrane into designated

brackets as shown in Figure 7.

(2) Push tube marked,

“RO IN” evenly

into the upper coupler on RO
membrane.

(3) Push tube marked,

“RO Left” evenly

into lower left coupler on RO
membrane.

(4) Push tube marked,

“RO Right” evenly

into lower right coupler on RO
membrane.

●

Removal procedure:

(1) Tubes are easily removed from

couplers, simply by pushing the
coupler collet in and pulling tube out.
(See Figure 9.)

※

Tubes are more easily removed by

pushing entire collet in, rather than
only a portion of it.

Figure 7

Figure 08

Figure 09

※

Once all three tubes have been connected, give each a gentle tug to verify that they are
connected securely.

※

When removing tubes, water may drip from RO membrane couplers. Be careful not to let water
get on the leak sensor.

Collet

Pull

RO IN

Upper coupler

Lower right
coupler

Lower left coupler

RO
Right

Left

Brackets

Summary of Contents for Pure Line WE200
























































Search results

Summary of Contents for Pure Line WE200

Reviews:

Yamato Pure Line WE200, Instruction Manual, Page: 17 / 55

Search results

Summary of Contents for Pure Line WE200

Reviews: