Yamaha YP125R Service Manual Download

Page: 197 / 498

FRONT BRAKE

4-22

EAS22220

INTRODUCTION

WARNING

EWA14101

Disc brake components rarely require disas-
sembly. Therefore, always follow these pre-
ventive measures:
• Never disassemble brake components un-

less absolutely necessary.

• If any connection on the hydraulic brake

system is disconnected, the entire brake
system must be disassembled, drained,
cleaned, properly filled, and bled after reas-
sembly.

• Never use solvents on internal brake com-

ponents.

• Use only clean or new brake fluid for clean-

ing brake components.

• Brake fluid may damage painted surfaces

and plastic parts. Therefore, always clean
up any spilt brake fluid immediately.

• Avoid brake fluid coming into contact with

the eyes as it can cause serious injury.

FIRST AID FOR BRAKE FLUID ENTERING
THE EYES:
• Flush with water for 15 minutes and get im-

mediate medical attention.

EAS22230

CHECKING THE FRONT BRAKE DISC

1. Remove:

• Front wheel

Refer to “FRONT WHEEL” on page 4-9.

2. Check:

• Brake disc

Damage/galling

→

Replace.

3. Measure:

• Brake disc deflection

Out of specification

→

Correct the brake disc

deflection or replace the brake disc.

▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼▼▼

a. Place the vehicle on a suitable stand so that

the front wheel is elevated.

b. Before measuring the front brake disc deflec-

tion, turn the handlebar to the left or right to
ensure that the front wheel is stationary.

c. Remove the brake caliper.
d. Hold the dial gauge at a right angle against

the brake disc surface.

e. Measure the deflection 1.5 mm (0.06 in) be-

low the edge of the brake disc.

▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲▲▲

4. Measure:

• Brake disc thickness

Measure the brake disc thickness at a few dif-
ferent locations.
Out of specification

→

Replace.

5. Adjust:

• Brake disc deflection

▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼▼▼

a. Remove the brake disc.
b. Rotate the brake disc by one bolt hole.
c. Install the brake disc.

TIP

Tighten the brake disc bolts in stages and in a
crisscross pattern.

Brake disc deflection limit

0.15 mm (0.0059 in)

Brake disc thickness limit

4.5 mm (0.18 in)

Front brake disc bolt

12 Nm (1.2 m·kgf, 8.7 ft·lbf)
LOCTITE®

Summary of Contents for YP125R



















































































































































































































































































































































































































































































































Search results

Summary of Contents for YP125R

Reviews:

Related manuals for YP125R

Brands by name

Popular brands

Yamaha YP125R, Service Manual

Search results

Summary of Contents for YP125R

Reviews:

Related manuals for YP125R

Brands by name

Popular brands