ENGINE (YP250R)
3-22
d. Measure the valve clearance with a thickness
gauge “1”.
Out of specification
→
Adjust.
▲▲▲
▲
▲ ▲▲▲
▲
▲ ▲▲▲
▲
▲ ▲▲▲
▲
▲ ▲▲▲
▲
▲ ▲▲▲
▲
▲▲▲
6. Adjust:
• Valve clearance
▼▼▼
▼
▼ ▼▼▼
▼
▼ ▼▼▼
▼
▼ ▼▼▼
▼
▼ ▼▼▼
▼
▼ ▼▼▼
▼
▼▼▼
a. Loosen the locknut “1”.
b. Insert a thickness gauge “2” between the end
of the adjusting screw and the valve tip.
c. Turn the adjusting screw “3” in direction “a” or
“b” with the tappet adjusting tool “4” until the
specified valve clearance is obtained.
d. Hold the adjusting screw to prevent it from
moving and tighten the locknut to specifica-
tion.
e. Measure the valve clearance again.
f. If the valve clearance is still out of specifica-
tion, repeat all of the valve clearance adjust-
ment steps until the specified clearance is
obtained.
▲▲▲
▲
▲ ▲▲▲
▲
▲ ▲▲▲
▲
▲ ▲▲▲
▲
▲ ▲▲▲
▲
▲ ▲▲▲
▲
▲▲▲
7. Install:
• Timing mark accessing plug
(along with the O-ring
)
• Camshaft sprocket cover
(along with the O-ring
)
• Tappet covers
(along with the O-rings
)
• Spark plug
• Spark plug cap
8. Install:
• V-belt case air filter cover
9. Install:
• Storage box
Refer to “GENERAL CHASSIS” on page 4-1.
Direction “a”
Valve clearance is increased.
Direction “b”
Valve clearance is decreased.
1
1
2
Tappet adjusting tool
90890-01311
Six piece tappet set
YM-A5970
T
R
.
.
Locknut (valve clearance adjust-
ing screw)
14 Nm (1.4 m·kgf, 10 ft·lbf)
T
R
.
.
Timing mark accessing plug
8 Nm (0.8 m·kgf, 5.8 ft·lbf)
Camshaft sprocket cover
10 Nm (1.0 m·kgf, 7.2 ft·lbf)
Tappet cover
10 Nm (1.0 m·kgf, 7.2 ft·lbf)
Spark plug
18 Nm (1.8 m·kgf, 13 ft·lbf)
3
b
a
b
a
4
New
New
New
Summary of Contents for YP125R
