Yamaha YP125R Service Manual Download | Manualshive

Page: 171 / 498

background image

ELECTRICAL SYSTEM

3-44

6. Install:

• Headlight bulb

NOTICE

ECA13690

Avoid touching the glass part of the head-
light bulb to keep it free from oil, otherwise
the transparency of the glass, the life of the
bulb and the luminous flux will be adversely
affected. If the headlight bulb gets soiled,
thoroughly clean it with a cloth moistened
with alcohol or lacquer thinner.

7. Attach:

• Headlight bulb holder

8. Connect:

• Headlight coupler

9. Install:

• Headlight bulb cover

10.Install:

• Front cowling assembly

Refer to “GENERAL CHASSIS” on page 4-1.

EAS21800

ADJUSTING THE HEADLIGHT BEAM

1. Adjust:

• Headlight beam (vertically)

▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼▼▼

a. Remove the adjusting screw accessing cap.
b. Turn the adjusting screw “1” in direction “a” or

“b”.

c. Install the adjusting screw accessing cap.

▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲▲▲

Direction “a”

Headlight beam is raised.

Direction “b”

Headlight beam is lowered.

1

2

3

New

1

1

a

a

b

b

«
...
169
170
171
172
173
...
»

Summary of Contents for YP125R



















































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for YP125R

Brand: E-Lux Pages: 40

Brand: DayMark Pages: 32

Brand: wayscral Pages: 256

Brand: Kaiser Baas Pages: 13

Brand: CITY BOSS Pages: 28

Brand: Jetson Pages: 24

SMART DRIFTING SCOOTER

Brand: Ultra Pages: 6

Brand: Yamaha Pages: 67

DART 350W Step-Over

Brand: Serfas Pages: 23

Brand: Yamaha Pages: 80

Brand: Van Os Medical B.V. Pages: 32

Brand: Orbea Pages: 34

Brand: Orthoquard Pages: 16

Brand: Wildfire Pages: 8

Brand: Phaewo Pages: 21

Brand: iSmart.emobility Pages: 70

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands